Problem: When the world's first underground railway opened in London in 1863, engineers had to work out how to operate steam trains safely underground and reduce the steam and smoke.
Engineering Solution: Engineers used conventional steam locomotives, but they were fitted with special pipes to condense the exhaust steam into side tanks of cold water. This meant less steam in the tunnels, but smoke was still a problem. Coke was used instead of coal as it creates less smoke, and there were ‘blow holes’ at intervals around the railway, but the atmosphere underground was still very unpleasant. The pollution problem was eventually overcome by electrification in the 1900s.
Come and see this wonder at LTM Covent Garden. Reference number: 1981/535
Problem: After the Second World War, London needed a bus that was easier to operate and maintain and a vehicle that used fuel more efficiently.
Engineering Solution: Engineers designed the Routemaster, a bus that had a lightweight aluminium frame, which reduced the strain on the engine. The Routemaster also had interchangeable body parts, making maintenance quicker and more efficient. Bus drivers welcomed the new power-steering, which made the vehicle much easier to drive.
Come and see this wonder at LTM Covent Garden. Reference number: 1991/23 part 0
Problem: With the introduction of deep-level tube railways from 1890, steam locomotives could no longer be used because of the lack of ventilation.
Engineering Solution: Electric traction was used to power the trains instead and electric locomotives were designed to fit in the smaller tube tunnels. The electricity used by the locomotives was generated by the Underground railway companies at power stations like Lots Road. It was the biggest power station in Europe when it opened in 1905.
Come and see this wonder at LTM Covent Garden. Reference number: 1991/18 part 0
Problem: Trams ran on fixed rails in the road. Maintaining the tracks cost a lot of money and passengers had to step out in the middle of the road to board the vehicles, which wasn’t safe.
Engineering Solution: In the 1930s, London Transport began to replace trams with the trolleybus, which was a cross between a tram and a bus. It had an electric motor like a tram, powered through overhead wires, but it ran on rubber tyres like a bus, not on fixed rails. With no track to maintain, operating costs were lower. Passengers found trolleybuses easier and safer to use because the vehicle could pull in to the kerb.
Come and see this wonder at LTM Covent Garden. Reference number: 1981/528 part 0
Problem: Operating a railway deep underground means you need to find an efficient way of getting passengers down to the platforms and back up to the surface.
Engineering Solution: Hydraulic lifts, powered by pressurised water, were installed at stations on London's first tube railway, the City & South London Railway, which opened in 1890. There are two cars in the shaft, each capable of carrying 50 people. The lifts were reliable, but slow. Much better than having to climb up and down 100 stairs though!
Come and see this wonder at LTM Covent Garden. Reference number: 1992/1
Problems: The first tunnels for the underground railway were built just below ground using the ‘cut and cover’ method. Building tunnels deep underground through London clay presented a different set of problems. The tunnels had to be strong, and wide enough for trains to travel through.
Engineering Solution: The invention of the Greathead shield revolutionised tunnelling, allowing circular tunnels to be built deep underground lined with strong iron rings. Tube tunnels were built up one ring at a time behind a shield. As the shield moved forward through the clay the curved sections were quickly put in place before the tunnel walls could collapse. Today it is done by machine, in the early days it was all by hand.
Come and see this wonder at LTM Acton Depot. Reference number: 1999/4235 part 0
Problem: As passenger numbers on the Underground increased at the beginning of the 20th century, more efficient ways of moving people to and from the platforms needed to be found.
Engineering Solution: An experimental, spiral moving walkway was installed in a spare lift shaft at Holloway Road station in 1906. It was patented by William Henry Aston and built by Jesse Reno, the American inventor who went on to develop the first working escalator. The spiral elevator was not a success and never operated in public service, but the first escalator was successfully installed at Earl’s Court in 1911.
Come and see this wonder at LTM Acton Depot. Reference number: 1999/876
Problem: Early railway signals and points were operated by large levers in signal boxes, connected by rods and wires to the equipment out on the ground. It was physically demanding work for the signalmen and the levers took up a lot of space.
Engineering Solution: The new Tube railways built in the 1900s introduced colour light signalling and electro-pneumatic points which could be controlled from compact power lever frames. The technical advance meant less space was needed for equipment and a lot less physical effort from the signalmen. The frame has an illuminated diagram showing the position of a train passing through the section of track. The wooden cabinet houses the mechanical interlocking gear that prevents points and signals being set in dangerous combinations.
Come and see this wonder at LTM Acton Depot. Reference number: 1993/5
Problem: After the First World War, passenger numbers on the buses increased and a vehicle with more capacity than the B type was required. But the police controlled the licensing regulations and these placed limits on vehicle size and weight.
Engineering Solution: Engineers at the London General Omnibus Company designed the K type, introduced in 1919, which seated 46 instead of 34 passengers. The driver’s seat was moved next to the engine instead of behind it and the body was made wider but with arches over the wheels. Consequently 12 more people could be accommodated in a design that was similar in size and weight to the vehicle it replaced.
Come and see this wonder at LTM Acton Depot. Reference number: 1981/515 part 0
Problem: Electricity is generated by power stations in the form of high voltage alternating current (AC) but Underground trains operate using a Direct Current (DC) system.
Engineering Solution: Mercury arc rectifiers converted the high voltage current from AC to DC at 600 volts. The rectifier is mounted on insulated struts and would have had safety barriers all around it because the exterior steel tank filled with mercury was ‘live’ with electricity when in use.
Come and see this wonder at LTM Acton Depot. Reference number: 1994/11
Our fan-favourite London Underground roundel lightbox just got a new younger sibling. This cute smaller version is just 7 inches tall and comes with three interchangeable inserts. Exclusively available at our shop!
Treat yourself to an day out with our newest Hidden London package - discover the abandoned Jubilee line platforms under Charing Cross station before a delicious afternoon tea at the Amba hotel.
This plaque was awarded to the winner of the District Railway station garden competition in 1916, a competition to recognise staff who enhanced stations with plants. It was dug up by a signalman in 1948.